Friday, June 29, 2007

L.E.D Products

D.B.R.T student made different types of led lamps in Fab lab.
1. Small Torch.
This torch is working on 9 volt DC battery. You can hang this torch on siling.
2. Big Torch
This torch is working on 6 volt DC battery. This torch is very useful to farmer. They can bring this torch in farm at night. Big light works up to 40 hours and small is up to 80 hours.
3. Emergency Lamp.
This lamp is useful for home. It is working 6 volt DC battery. It works up to 35 hours.


Hearing Aid


This low-cost, general-purpose electronic hearing aid works off 3V DC.
In this circuit, transistor and associated components from the audio signal preamplifier for the acoustic signals picked up by the condenser microphone and converted into corresponding electrical signal. The audio output of this circuit is 10 to 15mW and the quiescent current drain is below 1mA.


Tube Light Booster.

This is an applicative project. Power is a problem in rural Maharashtra and Quality of power just make situation worse. Basawling Patil D.B.R.T student took the initiative to make a tube light booster to solve this problem. This is a low cost device and can be afforded by any household.

Monday, June 18, 2007

Bell-Cum light Controller Circut
Bell cum light controller is a simple project done by DBRT students. There are four switches used in this project.Switch s1 is at the outer entry of the gate and is used by visitor.This switch activates the bell for the duration that switch is pressed.On its released the timer is initialised, which in turn switches on a bulb to light up path between the outer gate and house door.s2 switches on the light in the house for 3 minutes.It is used by the inhibitants of the house.It is used with the darkenss when s4 is ON.
When switch is pressed ON it activates the bell circuit only.It works even if the power is OFF as it runs on 3 volt battery.
switch s4 routes the supply to bulb through the relay.

Sunday, June 03, 2007

L.E.D Training program



Training Program was for IBT instructor and DBRT students from 21st May to 26th May by Sunil Bedse from pabal. Instructor from every corner of Maharashtra attended the program. Emergency torches and LED torches were assemble along with charger circuit.

These instructor will take this knowledge to the school they teach and it is exported at 2500 students will be benefited. We would like to thank DST(Department of science & technology) for helping us to spread the knowledge of LED.
Pedal Power Project





We made a pedal power cycle to generate electricity which in turn will charge the battery.

A uniquely designed flywheel was our innovaton.
It is a monowheel cycle and is attached to AC generator with V belt. We converted AC in DC and gave it to 12volt 32Ahr Battery
. We got 3Ampere Current at 1500 RPM. We used L.E.D lamps for lightning when the battery is charged. LED consumes only 2Watts of power.

We are planning to employ this project in tribal areas and Nomads where grid power is not an option as it is unaffordable to tribals and cannot be given to nomads who keep on moving from one place to another.

This mechanism is a big success in a Thane school where 32 children pedal for 15 minutes a day and develop uninterrupted power for their classrooms.

Wednesday, May 30, 2007

Electric power generation using dung bio gas.

Objective of this project is to generate electric power using bio gas.We use oil cakes and cow dung as feed for bio gas and this has worked excellently for our Bio Gas plant.

Idea:-
Idea is to generate electricity locally using dung bio gas.
This is an attempt to develop a model of producing electricity locally on small scale, and consume it within a short distance.

What is bio gas?
Bio gas is a mixture of gases, usually carbon dioxide and methane. It is produce by as a result of anaerobic decomposition of organic matter such as vegetable waste, animal waste. It is produce by a few kind of micro organism.
The active main flammable component is methane. Advantage of methane is that it dose not produce harmful carbon monoxide gas. So it is very good to use it in home.
As compare of with commercially available natural gas, Bio Gas contain a large preparation of carbon dioxide. So it is needed to remove such contain before using Bio Gas in IC engine. Process of filtration is important factor while using Bio Gas in internal combustion engine.

Approximate gases content in Bio Gas :-
  1. Methane(CH4) - 66.5%
  2. Carbon Dioxide(CO2) - 30.5%
  3. O2+N2 - 0.5%
  4. Humidity - 2.5%

(Source-Wikipedia and Chinese Bio gas manual)

COMPARISON OF CALORIFIC VALUE OF VARIOUS GASES

  1. Producers gas:-1200kcal/cum
  2. Landfill gas:-4000-5000kcal/cum
  3. Bio Gas:- 4500-6000kcal/cum
  4. Natural Gas:-6800-8000kcal/cum
  5. LPG:-10000-11000kcal/cum

(Source:- Blogg by Hement Thite)

POTENTIAL BIO GAS PRODUCTION FROM DIFFERENT FEEDSTOCK

Animal Quantity kg/day Bio Gas cum/day

Cattle west 10 0.36

Buffalo 15 0.54

Pigeon 2.25 0.18

Human 0.4 0.028

Chicken 0.18 0.11

Wednesday, March 07, 2007

Milk Tester Updates-:

This month we have taken readings with the new program that we were given by Neil,but unfortunately I used the old circuit.I was not able to load the program in the new circuit.This month there will be more work on the circuitry and the progarm so that I can use the new circuit as well as the program to take the readings.
Low cost hearing Aid-:

The low cost was hearing aid was ready for use this month.The Circuit diagram were picked from August 2003 issue of EFY.The circuit was modified further and now can give greater clarity of voice up to 4 meters.We are testing the circuit and we will finally promote it as low cost product for village people.

The cost of the circuit is less than Rs.80 and can be very handy.The dimensions are about 7 C.M. ,4 C.M. , 4 C.M. Its weight is also very low with batteries contributing most of it. We are working further to simplify the circuit more so that assembling the circuit becomes a layman's job.

Thursday, January 11, 2007

LOW COST HEARING AID

It is a unique project by FABLAB.IT has a simple circuitry that can be assembled by any one .
The cost of whole product can be less than a dollar and so it comes with great affordability to all the poor patients who dont have access to costly machines that can enhance there hearing ability.

Friday, December 22, 2006

Wind mill model using metal acrylic. It cut by laser cutter In fablab .


Students working in fablab .They makes different project . Using all machines .
Vigyan Ashram's model
All objects were cut through laser cutter .Using Qcad drawing programm.

Thursday, December 14, 2006

Feature
1.It operates on 230Volt AC.
2.Low cost
3.It's power consumption is 2 watts.
4.It gives light across 180 degree.


LED project fablab india
led lamp are connected in two type's
1) 24 LED connected in series form.
2) 24 LED connected in parallel form.

*24 LED connected in series form
The one LED required 4volt.max imam and 3 LED connected in series that way total voltage is given by .
V=L1+L2+L3 Where L1 is required 4 Volt.
=4+4+4
V=12
The 3 LED connected series form and required 3 Volt.When Voltage is applied to the across the lead of the LED,and the current start to flow.
LED bulb calculated power
input voltage V=12Volt.
current I=200MA.
calculated power P=VI.
P=12V*200MA
P=2.4W

Feature
1.It has low cost .
2.Has durability one years.
3.It has required minimum power.

24 LED connected in parallel form.

It has operated 4.5V,to give the 4.5V in connected in parallel form LED,but has required some more power.
LED bulb calculated power
input voltage V=4.5Volt.
current I=600MA.
calculated power P=VI.
P=4.5V*600MA
P=2.7W

Feature
1.It's required minimum voltage
2.It has low cost .
3.Has durability one years.
4.It has required minimum power.

Wednesday, October 18, 2006


Sky lamp.
Sky lamp made by students .

Wednesday, October 11, 2006




Designs made by students .


Friday, October 06, 2006




Milk tester ­

Milk tester is a novel project of fablab India. This tester can sense the changes in milk by step impulse responce . The research and development in project till today can identify different fluids but still some work needs to be done to sense changes in milk as it is in development stage.We are taking the readings for it.